|
|
The Original Clipdraw for 1911 Standard/Compact
For Model 1911 Pistols
(attaches on right side only)
Made from specially tempered spring steel with black powder coating or nickel plating.
Clipdraw fits these fine hand guns:
Part #1911 fits:
Model 1911 Standard Frame $19.99
Model 1911 Commander
Part #OM fits:
Colt Officer's Model
Colt Defender
Colt Compact
PLEASE NOTE: Parts #1911 and #OM will fit custom clones built on these EXACT same frames. Parts #1911 and #OM
will NOT fit other models such as Para-Ordnance, Beretta, Browning, Glock, etc.
|
|
|
Made from specially tempered spring steel with black oxide coating, Clipdraws are available to fit standard or large frame
Glocks. The Clipdraw comes with a slide cover plate that replaces the original and is drilled and tapped for attaching the
Clipdraw (see installation instructions below, figure 2).
Part #GS-B fits models 17, 19, 22, 23, 24,25, 26, 27,
28,31, 32, 33, 34, 35, 36
Part #GL-B fits models 20, 21, 29, 30, 37 $25.99
Glock Installation Instructions
Following the instruction in your Glock owners manual, remove the slide from the frame then separate the barrel and recoil
spring assembly from the slide. Following the instructions provided with your Clipdraw, remove the slide cover plate located
on the rear of the slide. Install the drilled and tapped slide cover plate provided with your Clipdraw. Mount the Clipdraw on
either side of the slide with the screws and allen wrench provided.
CAUTION (Reprint from the Glock owners manual)
Do not carry the pistol in the ready to fire condition. This is not the recommended safe-carrying method for civilian use. To
minimize risk of unintentional discharge, load live ammunition into the pistol only when you are ready to shoot.
Saf-T-Blok for Glocks:
Prevents accidental discharge!
|
|
|
For S&W Revolvers
(attaches on right side only)
Made from specially tempered spring steel with black powder coating or nickel plating.
Clipdraws are available to fit Smith & Wesson J, K or L frame revolvers. Custom round head screws are included to
replace the OEM countersunk screws.
Part #JF fits J frames. $19.99
Part #KF fits K and L frames.
PLEASE NOTE: #JF and #KF will ONLY fit revolvers manufactured by Smith & Wesson.
|
|
|
The "Universal" Clipdraw attaches in seconds with 3M Corp. #4941 VHB (very high bond) double coated tape. VHB tape
is used in the construction and aircraft industries as a replacement for rivets. It provides a 20 lb. continuous bond that resists
oil, solvents, heat and vibration. Heavy recoil and rapid slide movement have no effect on the bond strength between gun
and Clipdraw. The Clipdraw stays solidly in place with adhesion actually increasing over time. The "Universal" Clipdraw
consists of two parts. The mounting plate attaches to the gun with the double coated tape. The clip part screws to the
mounting plate with two 1/8" button head screws.
Switching to a holster is simple. Just remove the clip part and in most cases the gun can be holstered with the low profile
mounting plate left in place. No need to remove and replace the tape each time.
#SA mounts on either side of the slide or frame. Mounting requires just 3" x 1/4" of flat surface which can include grooved
or textured areas. VHB tape provides full adhesion on steel, aluminum or polymer surfaces.
#RV mounts on the right side of revolvers below the cylinder. It
requires just 2 ¾" x ¼" of flat surface for mounting.
$19.99
|
|
